Tandberg Data DPS Expansion Module Disk Pack Spécifications Page 35
- Page / 68
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
29
Installing and Configuring Additional Enclosures
Arrays are preconfigured on the DPS Expansion Module controller enclosure and any DPS
Expansion Module expansion enclosures shipped with it. You must install and configure any
drives and enclosures shipped separately. For every six drives, you can create an array or a
set of hot spares. You can attach up to four DPS Expansion Module expansion enclosures with
up to two arrays each to an DPS Expansion Module controller enclosure.
Adding arrays and enclosures to a DPS1000 Series configuration
Use the following procedures as you add arrays and enclosures to your current DPS1000
Series and DPS Expansion Module configuration.
Note
You must power off all DPS Expansion Module enclosures when you add arrays or
expansion enclosures. When an enclosure is powered off, all virtual tapes saved on its
arrays are unavailable to DPS1000 Series. Therefore, DPS1000 Series should be shut
down from its web interface and power should remain off until the arrays are fully
configured. This prevents users from trying to access inaccessible virtual tapes.
To add a second array to an XDC1200a or XDS1200a-1
1. Shut down DPS1000 Series from its web interface and power off any connected DPS
Expansion Module enclosures.
2. Install the drives. Refer to Installing drive carrier modules on page 18.
3. Create the array. Refer to Creating arrays on page 30.
4. Create the logical drive. Refer to Creating logical drives on page 32.
5. Power on DPS1000 Series.
6. Power on all connected DPS Expansion Module enclosures.
Note
When you connect a new DPS Expansion Module array to DPS1000 Series, DPS1000
Series will quickly start moving data to it to balance all DPS1000 Series storage. As a
result, DPS Expansion Module may be busy soon after it is powered on.
To add a set of hot spares to an XDC1200a or XDS1200a-1
1. Shut down DPS1000 Series from its web interface and power off any connected DPS
Expansion Module enclosures.
2. Install the drives. Refer to Installing drive carrier modules on page 18.
3. Create the hot spares. Refer to Designating hot spares on page 33.
- Installation and 1
- Administration Guide 1
- Contents 3
- About this guide 5
- Audience 5
- Typographical conventions 5
- Related documentation 6
- Overview 7
- 2 8
- Removing the disk I/O module 13
- Connecting power 29
- Powering DPS Expansion Module 30
- Accessing the serial console 31
- Setting an IP address 31
- Setting a static IP address 32
- Setting a dynamic IP address 32
- Accessing Help 33
- Setting up email notices 33
- Creating arrays 36
- Creating logical drives 38
- Designating hot spares 39
- Backing up the configuration 39
- Troubleshooting 41
- Drive failed to start 42
- Drive failed 42
- Power loss 43
- Power supply faults 43
- Thermal control issues 44
- Thermal alarm issues 44
- Thermal warnings 45
- 40 46
- Technical Specifications 53
- Power consumption 54
- Environment 55
- Interfaces - Disk I/O module 56
- Disk I/O module specification 57
- LEDs and Alarms 59
- Cooling fan module LED 60
- OPS panel LEDs 60
- RAID controller module LEDs 61
- Disk I/O module LEDs 62
- Drive carrier LEDs 63
- Visible alarms 64
- Audible alarms 64
- Index 67
- 62 68
Samsung T24E310EX manuels
Manuels d'utilisation et guides de l'utilisateur pour TV LCD Samsung T24E310EX.
Nous fournissons des manuels en pdf 2 Samsung T24E310EX à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels